How To Turn On Ignition Without Starting Engine Push Start – Do It Right!

A push-button ignition is not always easy to handle. This is where people wonder how to turn on ignition without starting engine push start.

You can learn how to start your car in simple steps.

We also explain who the push-button ignition is and what its benefits are.

If you want to install a push-button ignition in a vehicle, you can also find the steps you need to take.

How To Turn On Ignition Without Starting Engine Push Start

Some people wish to have the vehicle in ignition mode without starting the engine in certain situations.

This is a standardized process that is very easy to perform in most vehicles.

All that is required is that the vehicle has a fully charged battery in good condition to start the vehicle without starting the engine.

Ignition button

Of course, it is necessary to know where the ignition button is located on the vehicle. This button is incorporated into a wide variety of cars and other vehicles.

These vehicles no longer have the typical slot and classic key that many other vehicles use. Instead, it is an electronic key that allows for increased security.

So, there is an electronic ignition button located front and center, very close to the driver and front passenger seat.

Some models also incorporate a second ignition slot or button somewhere in the vehicle.

This backup button allows the vehicle to be started when the main button is not functioning.

This second backup button to start the vehicle may be located under the driver’s steering wheel.

This button may not only be located on the center console but may also be installed inside the glove box.

The second ignition backup button may also be installed under the cup holder on some vehicles.

This is the cup holder installed among each of the front seats.

Both the main ignition button and the backup button can be used to start the vehicle without starting the engine.

So, when the user has the vehicle’s electronic key, he/she can continue with the procedure.

Pressing the brake and the button

As mentioned above, this procedure is standardized for most manufacturers. While it is not the same procedure for all manufacturers, the process can be very similar.

In any case, the owner’s manual may indicate the exact steps to start the vehicle without starting the engine.

To do this, it is necessary to press the brake pedal and place the electronic key near the ignition button.

This will allow the vehicle’s system to recognize the electronic key and unlock all functions.

Once this step has been performed, the user only needs to press the ignition button once, twice, or three times.

The number of times the ignition button must be pressed to just get the ignition mode is detailed in the owner’s manual.

One example is found on several BMW models.

Here the user needs to press the ignition button three times quickly, which allows getting the ignition mode or diagnostic mode.

Check the battery

It is essential to consider that the ignition mode requires and consumes energy from the battery.

At the same time, the alternator is not running because the vehicle’s engine is off.

So, when the ignition mode is active, it may be challenging to start the vehicle engine when needed. That is why it is essential to have a new, fully charged battery.

Push Button Start: How Does It Work?

There are many advances in-vehicle security, one of which is the push-button ignition key fob.

This is a security breakthrough because it is the ultimate replacement for the classic vehicle keys.

These keys offer a much more convenient use and prevent the car from being used by any unauthorized person.

Although it is a popular type of key, it is not an advance that has become widespread in the automotive industry.

Most vehicles continue to use the classic key. However, this novel type of ignition provides a set of benefits that many users want to obtain.

  • Each start button is unique: the ignition signal is unique for each vehicle. This prevents or hinders the possibility of a vehicle being used by someone unauthorized.
  • Easier to use: that’s why many elderly people with arthritis prefer this type of key. They do not have to apply too hard pressure to turn the classic key and start the car.
  • More efficient ignition: the keyless ignition allows starting the engine even if the key fob has a discharged battery.
  • Decreased chances of accidents occur because the user needs to press the brake pedal before starting the vehicle.

How To Convert A Car To The Push Button Start

Due to the wide variety of benefits of the power button, many users wish to obtain this function.

However, only a few manufacturers have decided to implement push-button ignition in their vehicles.

Beyond that, there are some simple steps the user can take to install a push-button ignition.

Tools required

To perform this procedure, it is essential to have a few types of equipment.

  • Push-button starter kit
  • 10 mm screwdriver and wrench
  • Electrical tape and soldering iron
  • Wire stripper and multimeter

Once the user has all these elements, he/she can start by removing the observation cover.

Before that, it is essential to check the user’s manual included with any push-button starter kit.

This allows us to understand the distribution of the electrical cables that must be connected to do a good job.

Using the multimeter

Once everything is ready, select the DC mode on the multimeter. The proper ignition harness should be placed, and the left pin.

This should be done to check the voltage after connecting it all to a surface that is also grounded. The user needs to turn the key to check the voltage level.

Once the above step is done, the user needs to have the diagram to mark each of the wires. This diagram is essential as it allows the user to identify each type of wire.

Next, the user must start the engine by turning the key. Performing this step is what allows the multimeter to check the voltage.

The battery’s negative terminal must be disconnected with the 10 mm wrench. Only a tiny portion of the insulation on the cables should be removed to make the hole.

All this can be done using the wire stripper.

Making the connection

Each corresponding wire must pass through the hole that the user has drilled.

The ring transponder and the brake switch wires must be connected to complete the connection.

In turn, the two systems must be connected with a regular transponder. Finally, the starter button and covers must be reattached to finish.

FAQs On Push Button Start

What is the alternative way to start a car by using a push-button ignition?

Many vehicles are fitted with a keyless ignition system to increase security and provide other benefits.

However, the push-button start may not be working, and that is why a slot for a mechanical key is included.

A lot of people do not wish to take the mechanical key as an alternative to start their vehicle.

However, there is another way to start the vehicle without the starter button or the mechanical key.

The user needs to use their key fobs and press the button that indicates the start.

This is a backup system when the essential fob battery is dead. However, this backup system is only implemented by some manufacturers.

What is the solution for an ignition button that does not work?

The keyless entry system must detect the key fob to start the vehicle. Otherwise, the vehicle will not start because it is a security system.

Some people solve this problem by pressing the engine start button with the remote control. Yet, it is equally crucial to keep a fresh battery in the remote control.

Is it necessary to press the brake to start the vehicle?

Pressing the brake pedal is essential for many functions in today’s vehicles, including vehicles with a keyless start button.

Thus, to start the car, the user must first step on the foot brake.

Other vehicles with a conventional mechanical key and automatic transmission also require the brake to start the vehicle.

How to handle the brake to ignite the vehicle?

To start the vehicle’s engine in a car with a keyless ignition button, you must press the brake.

In general, the brake pedal must be fully depressed and held until the vehicle starts the engine.

After starting the vehicle and the engine, it is not required to keep holding the brake.

What if I can’t use the brake pedal?

One of the reasons for a hard brake pedal is the lack of vacuum pressure. Lack of vacuum pressure prevents the pushing rod to pull into the main body cylinder.

So, this could prevent a vehicle with a keyless ignition button from starting the engine.

Verdict

Knowing how to turn on ignition without starting engine push start allows you to be better prepared for the unexpected.

Today, many vehicles incorporate backup systems and modes so that the vehicle can be started anyway.

Knowing each of these backup modes allows you to use the vehicle in the event of failure or damage.

However, each user needs to keep in mind some fundamental aspects of this system.

The electronic key or remote control works with its internal battery. When this battery runs out or dies, using or starting the vehicle is more complicated.

The simplest way is to add a new battery to avoid all these problems. Also, it is crucial to check the condition of the vehicle’s battery.